Post Jobs

REX-USB60 DRIVER

But this makes it difficult to see the waveform in a low frequency region. An attempt was made to write parameter data that was outside the allowable range. This package installs the software Ethernet Controller driver. Tuning will end quickly if setting this to a value that you know will roughly match the moment of inertia. The following message then appears indicating the parameter is being written. Then reconnect the cable and restart the TOP software. Check the waveform to determine whether or not to make measurements again.

Uploader: Nikogul
Date Added: 7 June 2014
File Size: 32.90 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 68233
Price: Free* [*Free Regsitration Required]

Проект OpenNet: MAN uplcom (4) Специальные файлы /dev/* (FreeBSD и Linux)

Only CSV files can be loaded. Rex-usb60 there is no problem, use the default settings for rex-usv60 measurements. Click the [English] or [Japanese] button to select the menu language. It is especially useful for those who are required to download files continually. Use this software only after you are thoroughly familiar with its features and functions, safety information and rex-usb60.

Click to zoom out the X-axis in one step. Mechanical diagnostic measurements are to rex-usb60 used only as a rex-usb60. The larger the number of points, the higher the measurement accuracy, but the longer the time rex-usb60 uploading data.

When generation is completed, load the rex-usb60 data that rex-usb60 saved at step 1 above. Operating Procedures 1 Overall setup Read the following instructions and check if your machine is in safe condition.

New Drivers  OKIDATA C9650 DRIVER DOWNLOAD

Enter the maximum and minimum scales and then rex-usb60 the [OK] button. If failed to connect correctly, see section 4.

Rex Usb60 Usb Serial Converter Com4 Driver Download

The servo is still turned on at this point so click the [Stop] button C. When the trigger conditions are met or when you click the [Manual trigger] button in the above message box, the rex-usb60 driver transfers data to the PC and the following dialog box appears. When the robot driver rex-usb60 for a rotar y motor: Front panel connector marked “PC” PC Select “Install all data” or “Install individual data”, and click the [Start installation] button.

Operating Procedures 2 To set the digital trace conditions: After tuning ends, turn the SON terminal off, and turn the Rex-usb60 terminal on rex-usb60 then off, to rsx-usb60 the auto-tuning mode. The following initialization modes are selectable: General Contents Chapter 1 How to rex-usv60 1.

You might then be able to measure a clear waveform. Even when rex-us60 is interrupted before rex-usb60 is complete, turn the SON terminal off, and turn the RS terminal on and then off, to exit the autotuning mode.

When the resonance point is easily seen: Rex-usb60 Procedures Change the frequency range A explained earlier so that the measurement frequency is 5 times the frequency at the rec-usb60 estimated resonance point peakrex-usb60 then repeat from step rex-usb60 until a clear resonance point is obtained.

New Drivers  TOSHIBA DVD ROM SD R1202 DRIVER

Click this rex-usb60 to start writing the parameters. If the robot you are using is not in the list, you must add it to the generation models. When performing the generation rex-usb60, be sure to select the model to be used. The “Install rex-usb60 dialog box then appears.

Download your manual: Free user guides for all brands and devices!

The angle or distance per pulse differs depending on the rex-usb60 type when “rotary motor” rex-usb60 selected or on the linear sensor resolution when in “linear motor” type. Units rex-usb60 this parameter are as follows: Operating Procedures To run rex-usb60 jog: No matter how many times you change the settings, you might still be erx-usb60 rex-usb60 obtain an easy-to-see waveform depending on your machine. If a clear resonance point like this was not obtained, then make the measurement again as explained next.

rex-usb60 A confirmation dialog box appears. Set that position here in the number of trace points.